How to Put Fishing Line on a Spinning Reel?

Fishing line is an important part of fishing, and it is necessary to put the line on correctly in order to be successful. There are several different ways to put fishing line on a spinning reel, but this article will focus on the most common method. This method is suitable for both monofilament and braided lines.

First, you will need to thread the line through the guides on your rod. Start at the tip of the rod and work your way down. Next, tie the end of the line to the spool of your reel using a double overhand knot.

Be sure to leave enough slack so that you can make about 10-12 wraps around the spool. Once you have tied the knot, begin winding the line onto the spool by turning the handle of your reel clockwise. Continue winding until there is no more slack in the line and then cut off any excessline with scissors.

Congratulations-you have now successfully put fishing line on a spinning reel!

  • Unwind some fishing line from the spool and cut it to the desired length, using scissors
  • Tie a basic knot at the end of the line, leaving a long tail
  • Wrap the line around the base of the spool several times, going in the same direction for each wrap
  • Thread the long tail through the space between the wraps and pull it tight
  • Trim off any excess line

How To Put Line On A Spinning Reel

How Do I Put Line on My Spinning Reel?

Assuming you would like tips on spooling a spinning reel: First, you’ll need some fishing line. Choose the right pound test for the fish you’re going after and the conditions in which you’ll be fishing.

Then, cut off a length of line that’s twice as long as the rod. Next, locate the bail arm on your reel (it’s the wire arm that flips over the top of the spool when you’re ready to cast). Open it up so that you can see inside the spool.

Now, take hold of one end of your line and thread it through all of the guides on your rod until it comes out of the tip. Once it’s through, tie an overhand knot around one of the posts on your reel (this is called an arbor knot). Tighten this knot down so that it’s snug against the post, then pull about 6 inches of slack through and clip off any excess line.

Now comes time to actually start filling up your reel with line. Start by holding onto both ends of your line and letting some slack fall into the center of the spool. Grab onto just one end now and begin winding it around in a clockwise direction, making sure to keep tension on both sides so that your coils are nice and tight against each other.

Winding too loose will result in bird’s nests later on.

How Do You Put Line on a Spinning Reel Without Twist?

Assuming you’re referring to how to spool a spinning reel without line twist, there are a few things you can do: -Use a backing material before your main line. This will help fill the spool and provide a buffer between the main line and the spool, which will reduce friction and thus minimize the risk of line twist.

-Fill the spool only about 2/3 to 3/4 full. This will leave room for the line to expand as it’s being pulled off the reel, which again reduces friction and decreases the likelihood of twists forming. -Attach your lure or bait before you start reeling in.

That way, any twists that do form will be undone as soon as they reach your lure or bait and begin moving in the opposite direction.

How Do I Put Line on a Beginner Reel?

If you’re new to fishing, the process of putting line on a reel can seem daunting. But don’t worry – it’s actually quite simple! Just follow these steps and you’ll be ready to start reeling in those fish in no time.

1. Start by threading your line through the eyelet at the end of your rod. If you’re using a braided line, it’s best to use a leaders or backing before attaching your main line. This will help prevent wear and tear on your rod and reel.

2. Once your line is threaded through the eyelet, begin winding it around the spool of your reel. It’s important to wind it tightly, but not so tight that it causes friction or damage to the spool. 3. Continue winding until the spool is full, then tie a knot at the end of your line to keep it from unraveling.

Make sure the knot is secure before trimming off any excessline. And that’s all there is to it! Now you’re ready to start fishing like a pro.

Do You Put Line on a Spinning Reel Clockwise Or Counterclockwise?

When you’re winding line onto a spinning reel, you always want to wind it on in a clockwise direction. If you wind it on in a counterclockwise direction, you risk the line becoming tangled and unusable. So when you’re ready to start fishing with your spinning reel, make sure the line is wound on in a clockwise direction!

How to Put Fishing Line on a Spinning Reel?


How to Put Fishing Line on a Reel by Yourself

Fishing is a great hobby that can be enjoyed by people of all ages. If you’re new to fishing, one of the first things you’ll need to learn is how to put fishing line on a reel. This task may seem daunting at first, but it’s actually quite easy once you know what to do.

Here’s a step-by-step guide on how to put fishing line on a reel by yourself: 1. Start by threading the end of your fishing line through the eyelet at the bottom of the reel. 2. Wrap the line around the spool several times, making sure to overlap each layer slightly.

3. Once you’ve wrapped the line around the spool a few times, begin winding it tight using the handle on the side of the reel. Be sure to keep tension on the line as you wind so that it doesn’t come undone. 4. When you reach the end of your fishing line, tie it off securely with a double knot.

Trim any excessline and your reel is now ready for use!

How to Put New Fishing Line on

Fishing line is one of the most important tools in a fisherman’s arsenal, and it’s important to keep it in good condition. When it’s time to replace your fishing line, there are a few things you need to do to ensure that the process goes smoothly. First, you need to remove the old fishing line from your reel.

Start by removing the spool of old line and setting it aside. Then, use a knife or scissors to cut off any remaining line from the reel. Next, take a look at your new spool of fishing line and find the end with the attached tag.

Cut off this tag so that only about six inches of line remains. Now it’s time to start threading the new line onto your reel.

How to Put Fishing Line on a Closed Reel

Whether you’re a beginner or an experienced angler, there may come a time when you need to put fishing line on a closed reel. While it may seem like a daunting task, it’s actually quite simple once you know how. In this blog post, we’ll walk you through the steps of how to put fishing line on a closed reel, so you can get back to casting in no time.

What You’ll Need: -Fishing line -Scissors

-Pliers (optional) -Reel spool (closed) Instructions:

1. Start by cutting your fishing line to the desired length. If you’re using monofilament line, it’s best to leave about 10% extra so you have some room to work with if the line stretches while you’re casting. For braided or fused lines, cut the line so it is flush with the end of the spool.

2. Next, thread the end of the line through one of the eyelets on your reel spool and tie a double overhand knot. Make sure the knot is tight against the inside of the spool so it doesn’t come undone while you’re reeling in your catch. 3a.

If your reel has a bail arm, open it up and hold onto both sides of the spool with your thumb and forefinger before proceeding to step 4. 3b. If your reel does not have a bail arm (also called “closed face reels), hold onto both sides ofthe spool as shown in the image below before proceeding to step 4.

4a. For reels with a bail arm – Slowly start turning the handle while simultaneously letting go of one side ofthe spool until there is about 1/8 inch SPACE between whereyour fingers are gripping and The Line coming offofThe Spool as seen below . continue cranking The Handle slowly until all Of The Line has been let out .You might hear clicking sounds as The Bail Arm moves;this is normal . do not force The Bail Arm ,as this could damageYour Reel . Also , make sure thatyou keep tensiononThe Line at all times or else It will become tangled .


If you’re an avid fisherman, you know that having a well-functioning spinning reel is crucial to a successful day out on the water. But if you’re new to the sport, you might be wondering how to put fishing line on a spinning reel. Luckily, it’s not as complicated as it may seem.

Here’s a step-by-step guide on how to put fishing line on a spinning reel: 1. Start by removing the spool of line from the reel. If there’s already line on the spool, cut it off so that you have a clean surface to work with.

2. Next, tie one end of your new fishing line to the spool using an “arbor knot.” 3. Once the line is secure, start winding it onto the spool in a clockwise direction. As you wind, make sure to leave some slack in the line so that it doesn’t get too tight when you put it back on the reel.

4. When you’re finished winding, cut off any excess line and reattach the spool to the reel. You’re now ready to go fishing!

Scroll to Top